Crisp Solutions UC-515 Betriebsanweisung

Universal LCD Remote Control UC-515 With Touchscreen & Learning Function User’s Guide TM

Chapter 1-Introduction 4 NOTES

Chapter 2 GETTING STARTED This chapter will guide you through the steps for inserting the batteries and using the UCommand’s many features. Power Supp

Chapter 2-Getting Started 6 NOTE: Average alkaline battery life is approximately 4-6 months. If you do not use the remote for extended periods of ti

UCommand User’s Guide The LCD 7 • Be sure to replace the batteries if they have been used for longer than two years: there might be a danger of leakag

Chapter 2-Getting Started 8 • Avoid dropping the UCommand unit. • Don’t drop anything on the LCD touch screen. • Clean the LCD touch screen with a s

UCommand User’s Guide Touch Screen Buttons 9 11Device buttonsWhen you press the device button,the button’s icon will appear, indicatingthat it is curr

Chapter 2-Getting Started 10 NOTES

Chapter 3 OPERATING UCOMMAND UC-515 This chapter shows you how to set up UCommand, how to automatically configure devices, and how to use advanced fea

Chapter 3-Operating UCommand UC-515 12 Using the Learning Function When using the learning function, point your device’s remote control at UCommand’

UCommand User’s Guide Using the Learning Function 13 After you have lined up your remote control with UCommand’s learning eye, you can use the learnin

Preface ii About This User’s Guide This user’s guide is designed to assist you in setting up your UCommand UC-515 Universal LCD Remote Control. Inf

Chapter 3-Operating UCommand UC-515 14 The device screen appears again, with the LEARN icon above the Learn button. The Power button icon is blinki

UCommand User’s Guide Using the Learning Function 15 When you hear a beep and see the OK icon, release the button. The next button to be mapped will s

Chapter 3-Operating UCommand UC-515 16 When you have finished mapping all the desired buttons from your device remote control to UCommand, press the

UCommand User’s Guide Using the Delete Function 17 You will hear a beep, and then you will see the setup mode enable screen to the right. Note: This s

Chapter 3-Operating UCommand UC-515 18 Press the button whose data you want to delete. You will hear a beep and see the OKicon. The button’s data

UCommand User’s Guide Using the Delete Function 19 Press the device whose data you want to delete. You will hear two beeps, and will see the OKicon.

Chapter 3-Operating UCommand UC-515 20 Changing the LCD Layout The device Edit mode enables you to delete buttons or change the icons on buttons in

UCommand User’s Guide Changing the LCD Layout 21 Tap the screen once. The display will stop flashing. Press the button whose appearance you want to

Chapter 3-Operating UCommand UC-515 22 in device Edit mode or refer to Appendix A. After you have made your changes, press the device button again.

UCommand User’s Guide Macro Function 23 Press the macro button for three seconds. 1 1 You will hear a beep, and then you will see the setup mode en

UCommand User’s Guide iii Radio Frequency Interference This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

Chapter 3-Operating UCommand UC-515 24 First, press the button that you want to become the macro button. You can choose a button from any device scr

UCommand User’s Guide Macro Function 25 Macro Example The following example will help you to better understand recording a macro. This macro would be

Chapter 3-Operating UCommand UC-515 26 Press the TV button. Press the Power button. This will power the TV on. 1 Press TV/Video. This command will

UCommand User’s Guide Macro Function 27 You may need to set a time delay between turning your TV on and switching it to Video-input mode. Push the mac

Chapter 3-Operating UCommand UC-515 28 Press Power. This powers your VCR on. 1 Press Play. This command will start playing the tape in your VCR.

UCommand User’s Guide Adjusting the LCD Backlight 29 4. VCR turns on 5. VCR starts playing tape The macro button’s original function will not work unl

Chapter 3-Operating UCommand UC-515 30 Press each number button until it disappears. You will see the screen to the right. From here, you can se

UCommand User’s Guide Adjusting the LCD Backlight 31 UCommand detects the ambient lighting and will turn the backlight on according to the setting in

Chapter 3-Operating UCommand UC-515 32 When you have finished making your adjustment, press any of the Device buttons to exit. Turning Off the Beep

UCommand User’s Guide Recalling the Original LCD Layout 33 Recalling the Original LCD Layout You can reset the LCD panel buttons to their original fac

Preface iv Table of Contents Chapter 1 1 Introduction... 1 Unpacking UC

Chapter 3-Operating UCommand UC-515 34 NOTES

Appendix A UCOMMAND 515 SPECIFICATIONS Model UC-515 Display Touch LCD with backlight Display types TV, DSS/SAT/Cable, VCR, DVD, AMP, Tape/Tuner, CD,

Appendix A-All available Icons for the UCommand 36 ALL AVAILABLE ICONS FOR THE UCOMMAND

Appendix B TROUBLESHOOTING If you have trouble configuring or operating UCommand, first check that you have inserted the batteries correctly (page 5).

UCommand User’s Guide 38 You see an “error” display during the learning procedure. • Try the learning procedure again (page 12). • The source remote

UCommand User’s Guide UCommand UC-515 Universal LCD Remote Control User’s Guide 7-11-00/UG-515 Printed in Taiwan

UCommand User’s Guide v Recalling the Original LCD Layout ... 33 Figure 3-3: Recalling the original LCD panel c

Chapter 1 INTRODUCTION Congratulations on the purchase of UCommand UC-515, the easy to use and configure digital remote control. UCommand lets you ma

Chapter 1-Introduction 2 • UCommand UC-515, Universal LCD Remote Control • This User’s Guide • Reference Card • Registration Card If any of the abov

UCommand User’s Guide Identifying Components 3 Identifying Components This section provides an overview of UCommand’s features and controls. Please re